Over and Under Voltage Protector with Over Current Protector

Over and Under Voltage with Over Current Protertor
Over and Under Voltage Protector with Over Current Protector

Over and Under Voltage Protector with Over Current Protector

1、PURPOSE
The multi-function self-resetting reclosing protector integrates over-voltage protection, under-voltage protection, over-current protection and integrated intelligentprotector. When over-voltage, under-voltage and over-current obstacles appear in the line, this product can cut off the circuit instantaneously. Avoid unnecessary damage to electrical equipment. When the circuit returns to normal, the protector can automatically restore the circuit to make the electrical equipment work normally. The overvoltage value, undervoltage value, overcurrent value, circuit recovery time value and overcurrent protection reset time value of this product can be set by themselves. Adjust the parameters according to the local conditions and electrical conditions.
2、SPECIALTY
2.1 The product is fully compliant with the company's standard production of single-phase self-reclosing recloser.
2.2 When the line is over-voltage, under-voltage and over-current fault, the product automatically cuts off the line. When the line voltage or current returns to normal, the product automatically returns to normal power supply after the delay time set by the user, without manual operation.
2.3 The protector does not malfunction when the line is transient or transient overvoltage.
2.4 When the line is unstable due to some factors or suddenly powers off and then calls the state, the product will not be connected to the power source immediately. The delay time is set by the user according to the local situation.
2.5 The line voltage should not be high than 350VAC to prevent the product itself from being damaged due to excessive power supply voltage. If there is a need for a high power supply for a specific occasion, please contact the manufacturer.
3、SERVICE CONDITIONS
3.1 The ambient temperature does not exceed +50 degrees and not less than -10 degrees.
3.2 Installation location does not exceed 2000 meters above sea level.
3.3 Humidity: no more than 60%
4、INSTALLATION CONDITION
4.1 The protector can be installed vertically or horizontally in the cabinet..
4.2 It should be installed in a non-explosive medium, and there is no gas and conductive dust in the medium that is sufficient for the fermented metal
4.3 It should be installed in a place where there is no rain or snow.
5、TECHNICAL PARAMETERS
5.1 Rated voltage:220VAC 50Hz.
5.2 Rated current: 1A-60A adjustable (default 40A)
5.3 Over voltage cutoff value: 240V-300VAC adjustable (default 270VAC)
5.4 Under voltage cut-off value: 140V-200VAC adjustable (default 170VAC)
5.5 Over current cutoff value: 1A-60A adjustable (default 40A)
5.6 Power-on delay time and Relay on delay time : 3-60S adjustable (default 5S)
5.7 Reset delay time after overcurrent protection: 30-180S adjustable (default 30S)
5.8 Delay time when the product is overcurrent: 3S (overcurrent time is greater than this time will be confirmed as overcurrent and protection)
5.9 Power consumption:≤2W
5.10 Electrical mechanical life: ≥10Times
5.11 Dimensions: 86×37×66mm
6、SETUP

Over and Under Voltage Protector with Over Current Protector

7、USING
 After the protector is installed, the user can wire it and select the wire cross section according to the standard according to the current set by the protector. Note that the input and output of the protector cannot be error to avoid damage to the product or power failure.
8、ANNOUNCEMENTS
8.1 Users should follow the relevant procedures and pay attention to the following matters when performing various operations or tests to ensure the correct and safe use of this product.
8.2 Make proper wiring according to the input and output of the product identification (load current should be less than the protection current value of the product)
8.3 The neutral line N cannot be error and must be reliably wired, otherwise the protector will not work properly.
8.4 Before turning on the power, carefully check whether the wiring is correct, whether the load size matches the product current protection value, and whether the wiring screw is tightened, otherwise the product will be damaged.
8.5 After the product is powered on, do not touch the live parts to avoid electric shock.
8.6 This product needs to be short-circuit protected with micro-break, otherwise it will not be protected when the product load is short-circuited.
8.7 Since the product has an automatic reset function, after product is protected, the load (use of electrical appliances) should be removed immediately, and the circuit should be checked. Otherwise, the product will frequently switch on the load and disconnect the load, which will eventually run due to frequent overloading for a long time. Damage to the product or use of electrical appliances.
8.8 When not using this product for a long time, it should be protected from moisture and dust. Before use, the product should be tested according to the above, and it can be put into use after normal operation.
8.9 This product has no isolation function. Please disconnect the front-end breaker switch when repairing the line.
8.10 The N of this product is directly connected and has no disconnection function.
8,11 This product does not have excessive current short-circuit breaking capacity. Please install small circuit breakers such as DZ-47 and C65 at the front end of the line as overcurrent protection.

Over and Under Voltage Protector with Over Current Protector

Over and Under Voltage with Over Current Protertor
Over Current Protector
Over Voltage Protector
Under Voltage Protector
Voltage Protector
Current Protector

http://www.timer-switch.com
WhstsApp/imo/WeChat/Skype: 008613588987877
Email: anyelec@outlook.com

Over and Under Voltage with Over Current Protertor

Over and Under Voltage with Over Current Protertor
Over and Under Voltage Protector with Over Current Protector

Over and Under Voltage with Over Current Protertor

1、PURPOSE
The multi-function self-resetting reclosing protector integrates over-voltage protection, under-voltage protection, over-current protection and integrated intelligentprotector. When over-voltage, under-voltage and over-current obstacles appear in the line, this product can cut off the circuit instantaneously. Avoid unnecessary damage to electrical equipment. When the circuit returns to normal, the protector can automatically restore the circuit to make the electrical equipment work normally. The overvoltage value, undervoltage value, overcurrent value, circuit recovery time value and overcurrent protection reset time value of this product can be set by themselves. Adjust the parameters according to the local conditions and electrical conditions.

2、SPECIALTY
2.1 The product is fully compliant with the company's standard production of single-phase self-reclosing recloser.
2.2 When the line is over-voltage, under-voltage and over-current fault, the product automatically cuts off the line. When the line voltage or current returns to normal, the product automatically returns to normal power supply after the delay time set by the user, without manual operation.
2.3 The protector does not malfunction when the line is transient or transient overvoltage.
2.4 When the line is unstable due to some factors or suddenly powers off and then calls the state, the product will not be connected to the power source immediately. The delay time is set by the user according to the local situation.
2.5 The line voltage should not be high than 350VAC to prevent the product itself from being damaged due to excessive power supply voltage. If there is a need for a high power supply for a specific occasion, please contact the manufacturer.

3、SERVICE CONDITIONS
3.1 The ambient temperature does not exceed +50 degrees and not less than -10 degrees.
3.2 Installation location does not exceed 2000 meters above sea level.
3.3 Humidity: no more than 60%

4、INSTALLATION CONDITION
4.1 The protector can be installed vertically or horizontally in the cabinet..
4.2 It should be installed in a non-explosive medium, and there is no gas and conductive dust in the medium that is sufficient for the fermented metal
4.3 It should be installed in a place where there is no rain or snow.

5、TECHNICAL PARAMETERS
5.1 Rated voltage:220VAC 50Hz.
5.2 Rated current: 1A-60A adjustable (default 40A)
5.3 Over voltage cutoff value: 240V-300VAC adjustable (default 270VAC)
5.4 Under voltage cut-off value: 140V-200VAC adjustable (default 170VAC)
5.5 Over current cutoff value: 1A-60A adjustable (default 40A)
5.6 Power-on delay time and Relay on delay time : 3-60S adjustable (default 5S)
5.7 Reset delay time after overcurrent protection: 30-180S adjustable (default 30S)
5.8 Delay time when the product is overcurrent: 3S (overcurrent time is greater than this time will be confirmed as overcurrent and protection)
5.9 Power consumption:≤2W
5.10 Electrical mechanical life: ≥10Times
5.11 Dimensions: 86×37×66mm

6、SETUP

Over and Under Voltage with Over Current Protertor

7、USING
 After the protector is installed, the user can wire it and select the wire cross section according to the standard according to the current set by the protector. Note that the input and output of the protector cannot be error to avoid damage to the product or power failure.

8、ANNOUNCEMENTS
8.1 Users should follow the relevant procedures and pay attention to the following matters when performing various operations or tests to ensure the correct and safe use of this product.
8.2 Make proper wiring according to the input and output of the product identification (load current should be less than the protection current value of the product)
8.3 The neutral line N cannot be error and must be reliably wired, otherwise the protector will not work properly.
8.4 Before turning on the power, carefully check whether the wiring is correct, whether the load size matches the product current protection value, and whether the wiring screw is tightened, otherwise the product will be damaged.
8.5 After the product is powered on, do not touch the live parts to avoid electric shock.
8.6 This product needs to be short-circuit protected with micro-break, otherwise it will not be protected when the product load is short-circuited.
8.7 Since the product has an automatic reset function, after product is protected, the load (use of electrical appliances) should be removed immediately, and the circuit should be checked. Otherwise, the product will frequently switch on the load and disconnect the load, which will eventually run due to frequent overloading for a long time. Damage to the product or use of electrical appliances.
8.8 When not using this product for a long time, it should be protected from moisture and dust. Before use, the product should be tested according to the above, and it can be put into use after normal operation.
8.9 This product has no isolation function. Please disconnect the front-end breaker switch when repairing the line.
8.10 The N of this product is directly connected and has no disconnection function.
8,11 This product does not have excessive current short-circuit breaking capacity. Please install small circuit breakers such as DZ-47 and C65 at the front end of the line as overcurrent protection.

Over and Under Voltage with Over Current Protertor

Over and Under Voltage with Over Current Protertor
Over Current Protector
Over Voltage Protector
Under Voltage Protector
Voltage Protector
Current Protector

http://www.timer-switch.com
WhstsApp/imo/WeChat/Skype: 008613588987877
Email: anyelec@outlook.com

Muli at Sa ilalim ng Boltahe sa Over Current Protertor

Muli at Sa ilalim ng Boltahe sa Over Current Protertor

1. LAYUNIN
Ang multi-function na self-reset ng reclosing protector ay nagsasama ng proteksyon ng over-boltahe, proteksyon sa ilalim ng boltahe, over-kasalukuyang proteksyon at pinagsama-samang intelektwal. Kapag ang over-boltahe, sa ilalim ng boltahe at over-kasalukuyang mga hadlang ay lilitaw sa linya, ang produktong ito ay maaaring putulin ang circuit nang sabay-sabay. Iwasan ang hindi kinakailangang pinsala sa mga de-koryenteng kagamitan. Kapag bumalik ang normal na circuit, awtomatikong maibabalik ng tagapagtanggol ang circuit upang gawing normal ang mga de-koryenteng kagamitan. Ang halaga ng overvoltage, halaga ng undervoltage, labis na halaga, halaga ng oras ng pagbawi ng circuit at ang overcurrent na pag-reset ng halaga ng oras ng produktong ito ay maaaring itakda ng kanilang sarili. Ayusin ang mga parameter ayon sa mga lokal na kondisyon at kundisyon ng koryente.

2 、 ESPESYALTYA
2.1 Ang produkto ay ganap na sumusunod sa pamantayan ng produksyon ng kumpanya ng solong-reclosing na recloser na self-phase ng kumpanya.
2.2 Kapag ang linya ay over-boltahe, sa ilalim ng boltahe at labis na kasalukuyang pagkakamali, awtomatikong pinuputol ng produkto ang linya. Kapag ang linya ng boltahe o kasalukuyang bumalik sa normal, ang produkto ay awtomatikong bumalik sa normal na supply ng kuryente pagkatapos ng oras ng pagkaantala na itinakda ng gumagamit, nang walang manu-manong operasyon.
2.3 Ang tagapagtanggol ay hindi nagkakamali kapag ang linya ay lumilipas o lumilipas na overvoltage.
2.4 Kapag ang linya ay hindi matatag dahil sa ilang mga kadahilanan o biglang pinapagalitan at pagkatapos ay tumawag sa estado, ang produkto ay hindi makakonekta sa agad na mapagkukunan. Ang oras ng pagkaantala ay itinakda ng gumagamit ayon sa lokal na sitwasyon.
2.5 Ang linya ng boltahe ay hindi dapat mataas kaysa sa 350VAC upang maiwasan ang produkto mismo na mapinsala dahil sa labis na boltahe ng suplay ng kuryente. Kung may pangangailangan para sa isang mataas na supply ng kuryente para sa isang tiyak na okasyon, mangyaring makipag-ugnay sa tagagawa.

3 、 KOMBISYO NG SERBISYO
3.1 Ang temperatura ng ambient ay hindi lalampas sa +50 degree at hindi mas mababa sa -10 degree.
3.2 Ang lokasyon ng pag-install ay hindi lalampas sa 2000 metro sa itaas ng antas ng dagat.
3.3 Katamtaman: hindi hihigit sa 60%

4 、 PAGSULAT NG INSTALL
4.1 Ang tagapagtanggol ay maaaring mai-install nang patayo o pahalang sa gabinete ..
4.2 Dapat itong mai-install sa isang hindi pagsabog na daluyan, at walang gas at conductive dust sa daluyan na sapat para sa ferment metal
4.3 Dapat itong mai-install sa isang lugar kung saan walang ulan o niyebe.

5 、 Mga Teknikal na Teknikal
5.1 Rated boltahe: 220VAC 50Hz.
5.2 Na-rate kasalukuyang: 1A-60A adjustable (default 40A)
5.3 Higit sa halaga ng cutoff ng boltahe: 240V-300VAC madaling iakma (default 270VAC)
5.4 Sa ilalim ng halaga ng cut-off ng boltahe: naaayos ang 140V-200VAC (default default 170VAC)
5.5 Sa kasalukuyang halaga ng cutoff: naaayos ang 1A-60A (default 40A)
5.6 Power-on pagkaantala ng oras at Relay sa oras ng pagkaantala: 3-60S adjustable (default 5S)
5.7 I-reset ang oras ng pagkaantala pagkatapos ng overcurrent protection: 30-180S adjustable (default 30S)
5.8 Pag-antala ng oras kapag ang produkto ay overcurrent: 3S (overcurrent time ay mas malaki kaysa sa oras na ito ay makumpirma bilang overcurrent at proteksyon)
5.9 Pagkonsumo ng kuryente: ≤2W
5.10 Elektrikong mekanikal na buhay: :10Times
5.11 Mga Dimensyon: 86 × 37 × 66mm

6 、 SETUP

7 、 PAGGAMIT
 Matapos mai-install ang tagapagtanggol, maaaring i-wire ito ng gumagamit at piliin ang seksyon ng wire cross ayon sa pamantayan ayon sa kasalukuyang itinakda ng tagapagtanggol. Tandaan na ang input at output ng tagapagtanggol ay hindi maaaring maging error upang maiwasan ang pinsala sa produkto o pagkabigo ng lakas.

8 、 PAGTATAYA
8.1 Ang mga gumagamit ay dapat sundin ang mga kaugnay na pamamaraan at bigyang pansin ang mga sumusunod na bagay kapag nagsasagawa ng iba't ibang mga operasyon o pagsubok upang matiyak ang tama at ligtas na paggamit ng produktong ito.
8.2 Gumawa ng wastong mga kable ayon sa pag-input at output ng pagkakakilanlan ng produkto (ang kasalukuyang kasalukuyang load ay dapat na mas mababa sa proteksyon ng kasalukuyang halaga ng produkto)
8.3 Ang neutral na linya N ay hindi maaaring maging error at dapat na maaasahang wired, kung hindi man ay hindi gagana nang maayos ang tagapagtanggol.
8.4 Bago i-on ang lakas, maingat na suriin kung tama ang mga kable, kung ang sukat ng pag-load ay tumutugma sa halaga ng kasalukuyang proteksyon ng produkto, at kung mahigpit ang wiring screw, kung hindi man ay masisira ang produkto.
8.5 Matapos mapalakas ang produkto, huwag hawakan ang mga live na bahagi upang maiwasan ang shock shock.
8.6 Ang produktong ito ay kailangang ma-circuit na protektado ng micro-break, kung hindi, hindi ito maprotektahan kapag ang pag-load ng produkto ay maiksi.
8.7 Yamang ang produkto ay may awtomatikong pag-reset ng pag-reset, pagkatapos na protektado ang produkto, ang pag-load (paggamit ng mga de-koryenteng kasangkapan) ay dapat na tinanggal agad, at dapat na suriin ang circuit. Kung hindi man, ang produkto ay madalas na lumipat sa pag-load at idiskonekta ang pag-load, na sa kalaunan ay tatakbo dahil sa madalas na labis na karga sa loob ng mahabang panahon. Pinsala sa produkto o paggamit ng mga de-koryenteng kagamitan.
8.8 Kapag hindi ginagamit ang produktong ito sa mahabang panahon, dapat itong protektahan mula sa kahalumigmigan at alikabok. Bago gamitin, ang produkto ay dapat na masuri ayon sa nasa itaas, at maaari itong magamit pagkatapos ng normal na operasyon.
8.9 Ang produktong ito ay walang pag-ihiwalay. Mangyaring idiskonekta ang switch ng front-end breaker kapag nag-aayos ng linya.
8.10 Ang N ng produktong ito ay direktang konektado at walang pagpapaandar na pag-disconnect.
8,11 Ang produktong ito ay walang labis na kasalukuyang kapasidad ng pagsira ng maikling circuit. Mangyaring mag-install ng mga maliliit na circuit breaker tulad ng DZ-47 at C65 sa harap na dulo ng linya bilang sobrang proteksyon.

9 、 KONNECTION DIAGRAM

Patuloy at Sa ilalim ng Boltahe na may Higit sa Kasalukuyang Protertor, Sa Kasalukuyang Tagapangalaga, Over Voltage Protector, Sa ilalim ng Voltage Protector
http://www.timer-switch.com
Skype: anyrelay
Email: anyelec@outlook.com

Over and Under Voltage with Over Current Protertor

Over and Under Voltage with Over Current Protertor
1、PURPOSE
The multi-function self-resetting reclosing protector integrates over-voltage protection, under-voltage protection, over-current protection and integrated intelligentprotector. When over-voltage, under-voltage and over-current obstacles appear in the line, this product can cut off the circuit instantaneously. Avoid unnecessary damage to electrical equipment. When the circuit returns to normal, the protector can automatically restore the circuit to make the electrical equipment work normally. The overvoltage value, undervoltage value, overcurrent value, circuit recovery time value and overcurrent protection reset time value of this product can be set by themselves. Adjust the parameters according to the local conditions and electrical conditions.

2、SPECIALTY
2.1 The product is fully compliant with the company's standard production of single-phase self-reclosing recloser.
2.2 When the line is over-voltage, under-voltage and over-current fault, the product automatically cuts off the line. When the line voltage or current returns to normal, the product automatically returns to normal power supply after the delay time set by the user, without manual operation.
2.3 The protector does not malfunction when the line is transient or transient overvoltage.
2.4 When the line is unstable due to some factors or suddenly powers off and then calls the state, the product will not be connected to the power source immediately. The delay time is set by the user according to the local situation.
2.5 The line voltage should not be high than 350VAC to prevent the product itself from being damaged due to excessive power supply voltage. If there is a need for a high power supply for a specific occasion, please contact the manufacturer.

3、SERVICE CONDITIONS
3.1 The ambient temperature does not exceed +50 degrees and not less than -10 degrees.
3.2 Installation location does not exceed 2000 meters above sea level.
3.3 Humidity: no more than 60%

4、INSTALLATION CONDITION
4.1 The protector can be installed vertically or horizontally in the cabinet..
4.2 It should be installed in a non-explosive medium, and there is no gas and conductive dust in the medium that is sufficient for the fermented metal
4.3 It should be installed in a place where there is no rain or snow.

5、TECHNICAL PARAMETERS
5.1 Rated voltage:220VAC 50Hz.
5.2 Rated current: 1A-60A adjustable (default 40A)
5.3 Over voltage cutoff value: 240V-300VAC adjustable (default 270VAC)
5.4 Under voltage cut-off value: 140V-200VAC adjustable (default 170VAC)
5.5 Over current cutoff value: 1A-60A adjustable (default 40A)
5.6 Power-on delay time and Relay on delay time : 3-60S adjustable (default 5S)
5.7 Reset delay time after overcurrent protection: 30-180S adjustable (default 30S)
5.8 Delay time when the product is overcurrent: 3S (overcurrent time is greater than this time will be confirmed as overcurrent and protection)
5.9 Power consumption:≤2W
5.10 Electrical mechanical life: ≥10Times
5.11 Dimensions: 86×37×66mm

6、SETUP

7、USING
 After the protector is installed, the user can wire it and select the wire cross section according to the standard according to the current set by the protector. Note that the input and output of the protector cannot be error to avoid damage to the product or power failure.

8、ANNOUNCEMENTS
8.1 Users should follow the relevant procedures and pay attention to the following matters when performing various operations or tests to ensure the correct and safe use of this product.
8.2 Make proper wiring according to the input and output of the product identification (load current should be less than the protection current value of the product)
8.3 The neutral line N cannot be error and must be reliably wired, otherwise the protector will not work properly.
8.4 Before turning on the power, carefully check whether the wiring is correct, whether the load size matches the product current protection value, and whether the wiring screw is tightened, otherwise the product will be damaged.
8.5 After the product is powered on, do not touch the live parts to avoid electric shock.
8.6 This product needs to be short-circuit protected with micro-break, otherwise it will not be protected when the product load is short-circuited.
8.7 Since the product has an automatic reset function, after product is protected, the load (use of electrical appliances) should be removed immediately, and the circuit should be checked. Otherwise, the product will frequently switch on the load and disconnect the load, which will eventually run due to frequent overloading for a long time. Damage to the product or use of electrical appliances.
8.8 When not using this product for a long time, it should be protected from moisture and dust. Before use, the product should be tested according to the above, and it can be put into use after normal operation.
8.9 This product has no isolation function. Please disconnect the front-end breaker switch when repairing the line.
8.10 The N of this product is directly connected and has no disconnection function.
8,11 This product does not have excessive current short-circuit breaking capacity. Please install small circuit breakers such as DZ-47 and C65 at the front end of the line as overcurrent protection.

9、CONNECTION DIAGRAM

http://www.timer-switch.com
Skype: anyrelay
Email: anyelec@outlook.com